Step 1: Clean the surface of your desired location. We recommend using rubbing alcohol and letting them air dry. 
         

            Tip: Very clean and dry surfaces create the best adhesion! 

Step 2: Peel off the clear cover of the Nano Tape (located at the bottom of each divider) and stick them on the exact location.

            Tip: Press as hard as you can on each divider for best adhesion! 

Step 1: Hold on to the top edges of the divider and tilt them to the side until adhesive starts to come off. 
         

            Note: The Nano Tape will remain intact and on the unit. Removing the dividers will not affect its adhesion.  

Step 2: Wipe the Nano Tape with a damp, lint-free cloth and let it air dry for at least 10 minutes.

            Important: DO NOT use paper towel for cleaning! After air drying for 10 minutes, DO NOT test dryness with your fingers. 

                                 Oil and dirt will decrease the Nano Tape's strength. 

Should you need further assistance, please do not hesitate to send us an email at support@beeneatproducts.com. We're more than happy to assist you! 

• 36 x AAA Battery
• 54 x AA Battery
• 5 x 9V Battery
• 5 x C Battery
• 4 x D Battery
• up to 10 x Button Battery (depends on size)

Step 1: Use a pencil to mark the screw locations on the wall.

           Tip: 2 of them are located in the top row of the AAA Battery Slots and 1hole is in the bottom of C Battery Slot. 

Step 2: Pre-drill the marked locations on the wall and install the Wall Anchors. 

Step 3: Attach the Battery Rack on the wall and tighten the screw.

             Important:DO NOT overtighten the screws. 

• The needle in the meter will indicate the state of the battery in the dial
• This tester DOES NOT test6V or 12V Batteries

• Dispose of old batteries promptly and properly
• Keep out of the reach of children and pets
• Swallowing a battery is extremely dangerous

Should you need further assistance, please do not hesitate to send us an email at support@beeneatproducts.com. We're more than happy to assist you!   

Step 1: Place the riser under each corner of the bed. 
         

            Tip: If the mattress and box spring are already in place, have one person lift the corner while the other slides the Riser.  

Step 2: Position the leg of the frame in the ridge at the top of each Riser.

            Tip: Place the Risers first under both legs at the bottom of the bed, then the legs at the head.  

Step 1: Consult with a qualified electrician if the Risers are properly grounded. 
         

            Important: DO NOT modify the plug provided - if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

Step 2: Only plug the Risers into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

            Note: The Risers are equipped with a cord having an equipment-grounding conductor and a grounding plug. 

• Wipe the unit with a soft damp cloth. DO NOT use abrasive cleaners or spray liquids. 
• Store in dry location, away from hot and/or sharp objects.

• Make sure the Green Light is illuminated to ensure proper charging of all devices. 
• Avoid plugging 2 high amperage, fast-charge devices at the same time. This causes the USB ports to shut down. 
• If the Green Light turns off, unplug 1 one of the charging devices. Charging continues a few seconds after the Green Light turns back on.

• Ensure proper installation because there's a risk of tip over
• Supports a maximum weight of 350 lbs per Riser
• Diameter of furniture leg SHALL NOT be less than 1.5 inches. 

Should you need further assistance, please do not hesitate to send us an email at support@beeneatproducts.com. We're more than happy to assist you!     

Step 1: Attach the cross divider and spring-loaded divider together. 
         

            Tip: Align the holes on each of the dividers and squeeze to secure.  

Step 2: Create custom partitions based on your organization needs and insert the attached dividers into the drawer.

            Tip: Fully expand the divider and compress the spring cap for a sturdy, snug fit.  

Step 3: Install cross dividers between spring-loaded dividers.

            Tip: Ensure that the release buttons are facing each other.   

To remove or adjust the dividers, simply push the black release button to unlock the attached dividers. 

After the final placement, use the included double-sided tape to stick the dividers more securely to the drawer wall. 

Should you need further assistance, please do not hesitate to send us an email at support@beeneatproducts.com. We're more than happy to assist you!